Screw the valve back into the housing, being careful not to strip or over tighten the threads. The portion of the valve the handle sits on is grooved to correspond to the handle. Hold it with the pliers and ease it out of the faucet. If your faucet valves are not directly above your water supply lines, you'll need to bend the top portion of the rigid supply lines into an S shape so they will reach the valves and screw onto them straight. Add thread tape to the end of the pipe. You need to remove this nut and pull out the washer. If there are, repeat the steps and try another washer.
For braided supply lines: Screw the ½-inch compression fitting to the faucet valve. As an extra precaution put masking tape around the jaws of the pliers. Assess what type of faucet stems you have. Replacing your faulty hardware is a common fix, but by repairing your valve or stem. Then tighten the mounting nut to the sink from underneath. It will be held in place by a screw. Inside the hole, locate the screw and, with a Phillips screwdriver, turn the screw to the left to loosen and take it out along with the handle.
However, the benefits of a new faucet should outweigh your hesitance. Please give us some insight as to what kind of faucet we have. The first method : replace the bathtub faucet stems 1. Adjust them so they face straight to the sides when turned off and straight forward when on. Cut the pipe going up to the shower, as well as the hot and cold lines below.
I have tried to remove by twisting both directions. Add 13% to 22% to the total cost above if a general contractor will supervise this project. Do you have an old bathtub faucet that leaks, doesn't work right, or is just plain ugly? Apply caulk to the base of the spout and screw it in place. To create this article, volunteer authors worked to edit and improve it over time. If the end is smooth, use sand paper to rough the end of the pipe and then slide on the spout. Finger tighten all four nuts. Screw the handle on the stem : you must screw the handle in the same position as it was before you removed it, so be sure to reattach the handles in the same position.
Add thread tape to the end of the showerhead pipe and screw the head into place. This new faucet should have the same measurements as your old faucet so that it can easily screw into the wall. Be sure the replacement washer is an exact match and coated with petroleum jelly. As a precaution you can put masking tape around each of the jaws of the pliers. To create this article, volunteer authors worked to edit and improve it over time. Test that the stopper opens high enough to let water out. If the handle uses a setscrew, replace that accordingly.
Faucet Installation by Brand Most faucet hardware installations are simple. The stopper moves via this ball joint whenever the lift rod moves. How can find my problem. Turn on the water supply, and check for leaks. If there are leaks it means the connections are not tight enough. But a steady flow may indicate a leak.
Take the valve stems to a home goods or plumbing supply store to find washers and seals that are the correct size. After it cools, place the O-ring back on and screw the tub spout onto the adapter by turning it clockwise. It looks like white string and it comes in varying thicknesses. It will be one of three kinds: a screw-on spout with threads deep inside the spout; a screw-on spout with the threads at the back of the spout; or a spout that requires a setscrew underneath. Replace it with a matching new one.
Before removing or replacing the handles, look to see how they are attached to the valve stems. Remember the position they were in before you removed them and be sure to reattach them in that same position. Move it around to check on this. If not, use the wrench to remove it. If you have a third handle, it is usually to divert water between the tub and a shower head.
Slide the drain rim up into the drain hole from beneath. To learn how to replace a bathtub faucet spout, scroll down! Try the flat washer first. This article has also been viewed 392,859 times. There are several different ways the spout could be connected, depending on how it is internally connected to the plumbing. Not to mention that they have the right tools for the job! Hand-tighten the three-way spout tee at the spout's bottom as shown , leaving the openings facing the hot and cold valves.